Analog Input Module 6ES7134-6JD00-0CA1
SIMATIC SIEMENS ET 200SP, Analog input module , AI 4xRTD/TC High Feature, suitable for BU type A0, A1, Color code CC00, channel diagnostics, 16 bit, +/-0.1%, 2-/3-/4-wire
| SIEMENS | |
General information |
|
| Product type designation | AI 4x RTD/TC 2/3/4-wire HF, PU 1 |
| HW functional status | From FS08 |
| Firmware version
● FW update possible |
Yes |
| usable BaseUnits | BU type A0, A1 |
| Color code for module-specific color identification plate | CC00 |
| Product function | |
| ● I&M data | Yes; I&M0 to I&M3 |
| ● Adjustment of measuring range | Yes |
| Engineering with | |
| ● STEP 7 TIA Portal configurable/integrated as of version | V14 |
| ● STEP 7 configurable/integrated as of version | V5.6 |
| ● PCS 7 configurable/integrated as of version | V8.1 SP1 |
| ● PROFIBUS as of GSD version/GSD revision | One GSD file each, Revision 3 and 5 and higher |
| ● PROFINET as of GSD version/GSD revision | GSDML V2.3 |
| Operating mode | |
| ● Oversampling | No
No |
| ● MSI | |
| CiR – Configuration in RUN | |
| Reparameterization possible in RUN | Yes |
| Calibration possible in RUN | Yes |
| Supply voltage | |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current | |
| Current consumption, max. | 35 mA |
| Power loss | |
| Power loss, typ. | 0.75 W |
Address area |
|
| Address space per module | |
| ● Address space per module, max. | 8 byte; + 1 byte for QI information |
| Hardware configuration | |
| Automatic encoding | Yes |
| ● Mechanical coding element | Yes |
| Selection of BaseUnit for connection variants | |
| ● 2-wire connection | BU type A0, A1 |
| ● 3-wire connection | BU type A0, A1 |
Analog inputs |
|
| Number of analog inputs | 4 |
| permissible input voltage for voltage input (destruction limit), max. | 30 V |
| Cycle time (all channels), min. | Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels); for line compensation in case of a three-wire connection, an additional cycle is necessary |
| Technical unit for temperature measurement adjustable | Yes; °C/°F/K |
| Input ranges (rated values), voltages | |
| ● -1 V to +1 V | Yes; 16 bit incl. sign |
| ● Input resistance (-1 V to +1 V) | 1 MΩ |
| ● -250 mV to +250 mV | Yes; 16 bit incl. sign |
| ● Input resistance (-250 mV to +250 mV) | 1 MΩ |
| ● -50 mV to +50 mV | Yes; 16 bit incl. sign
1 MΩ |
| ● Input resistance (-50 mV to +50 mV) |
| ● Input resistance (Ni 500) | 1 MΩ
Yes; 16 bit incl. sign |
| ● Pt 100 | |
| ● Input resistance (Pt 100) | 1 MΩ |
| ● Pt 1000 | Yes; 16 bit incl. sign |
| ● Input resistance (Pt 1000) | 1 MΩ |
| ● Pt 200 | Yes; 16 bit incl. sign |
| ● Input resistance (Pt 200) | 1 MΩ |
| ● Pt 500 | Yes; 16 bit incl. sign |
| ● Input resistance (Pt 500) | 1 MΩ |
| Input ranges (rated values), resistors | |
| ● 0 to 150 ohms | Yes; 15 bit |
| ● Input resistance (0 to 150 ohms) | 1 MΩ |
| ● 0 to 300 ohms | Yes; 15 bit |
| ● Input resistance (0 to 300 ohms) | 1 MΩ |
| ● 0 to 600 ohms | Yes; 15 bit |
| ● Input resistance (0 to 600 ohms) | 1 MΩ |
| ● 0 to 3000 ohms | Yes; 15 bit |
| ● Input resistance (0 to 3000 ohms) | 1 MΩ |
| ● 0 to 6000 ohms | Yes; 15 bit |
| ● Input resistance (0 to 6000 ohms) | 1 MΩ |
| ● PTC | Yes; 15 bit |
| ● Input resistance (PTC) | 1 MΩ |
| Thermocouple (TC) | |
| Temperature compensation | |
| — parameterizable | Yes |
| — Reference channel of the module | Yes |
| — internal comparison point | Yes; with BaseUnit type A1 |
| — Reference channel of the group | Yes |
| — Number of reference channel groups | 4; Group 0 to 3 |
| — fixed reference temperature | Yes |
Cable length |
|
| ● shielded, max. | 200 m; 50 m with thermocouples |
| Analog value generation for the inputs | |
| Measurement principle | integrating (Sigma-Delta) |
| Integration and conversion time/resolution per channel | |
| ● Resolution with overrange (bit including sign), max. | 16 bit |
| ● Integration time, parameterizable | Yes |
| ● Basic conversion time, including integration time (ms) |
| — additional processing time for wire-break check | 2 ms; In the ranges resistance thermometers, resistors and thermocouples
2 ms; for 3/4 wire transducer (resistance thermometer and resistor) |
| — additional power line wire-break check | |
| ● Interference voltage suppression for interference frequency f1 in Hz | 16.6 / 50 / 60 Hz |
| ● Conversion time (per channel) | 180 / 60 / 50 ms |
| Smoothing of measured values | |
| ● Number of smoothing levels | 4; None; 4/8/16 times |
| ● parameterizable | Yes |
| Encoder | |
| Connection of signal encoders | |
| ● for voltage measurement | Yes |
| ● for resistance measurement with two-wire connection | Yes |
| ● for resistance measurement with three-wire connection | Yes |
| ● for resistance measurement with four-wire connection | Yes |
| Errors/accuracies | |
| Linearity error (relative to input range), (+/-) | 0.01 %; ±0.1 % for resistance thermometers and resistance |
| Temperature error (relative to input range), (+/-) | 0.0009 %/K; ±0.005 % / K at thermocouple |
| Crosstalk between the inputs, min. | -50 dB |
| Repeat accuracy in steady state at 25 °C (relative to input range), (+/-) | 0.05 % |
| Operational error limit in overall temperature range | |
| ● Voltage, relative to input range, (+/-) | 0.1 % |
| ● Resistance, relative to input range, (+/-) | 0.1 % |
| Basic error limit (operational limit at 25 °C) | |
| ● Voltage, relative to input range, (+/-) | 0.05 % |
| ● Resistance, relative to input range, (+/-) | 0.05 % |
| Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency | |
| ● Series mode interference (peak value of interference < rated value of input range), min. | 70 dB |
| ● Common mode voltage, max. | 10 V |
| ● Common mode interference, min. | 90 dB |
Isochronous mode |
|
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information | |
| Diagnostics function | Yes |
| Alarms | |
| ● Diagnostic alarm | Yes
Yes; two upper and two lower limit values in each case |
| ● Limit value alarm | |
| Diagnostic messages | |
| ● Monitoring the supply voltage | Yes |
| ● Wire-break | Yes; channel by channel |
| ● Group error | Yes |
| ● Overflow/underflow | Yes; channel by channel |
| Diagnostics indication LED | |
| ● Monitoring of the supply voltage (PWR-LED) | Yes; Green PWR LED |
| ● Channel status display | Yes; Green LED |
| ● for channel diagnostics | Yes; Red LED |
| ● for module diagnostics | Yes; green/red DIAG LED |
| Potential separation | |
| Potential separation channels | |
| ● between the channels | No |
| ● between the channels and backplane bus | Yes |
| ● between the channels and the power supply of the electronics | Yes |
Isolation |
|
| Isolation tested with | 707 V DC (type test) |
| Ambient conditions | |
| Ambient temperature during operation | |
| ● horizontal installation, min. | -30 °C |
| ● horizontal installation, max. | 60 °C |
| ● vertical installation, min. | -30 °C |
| ● vertical installation, max. | 50 °C |
| Altitude during operation relating to sea level | |
| ● Installation altitude above sea level, max. | 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual |
| Dimensions | |
| Width | 15 mm |
| Height | 73 mm |
| Depth | 58 mm |
| last modified: | 01/20/2020 |
SIEMENS Analog Input Module 6ES7134-6JD00-0CA1
