نقد و بررسی :
Analog Output Module 6ES7135-6HD00-0BA1
Analog Output Module 6ES7135-6HD00-0BA1
SIMATIC ET 200SP, Analog output module, AQ 4XU/I Standard, suitable for BU type A0, A1, Color code CC00, Module diagnostics, 16 bit, +/-0.3%
SIEMENS |
General information
|
|
Product type designation |
AQ 4xU/I ST |
HW functional status |
From FS07 |
usable BaseUnits |
BU type A0, A1 |
Color code for module-specific color identification plate |
CC00 |
Product function |
|
● I&M data |
Yes; I&M0 to I&M3 |
● Output range scalable |
No |
Engineering with |
|
● STEP 7 TIA Portal configurable/integrated as of version |
V11 SP2 / V13 |
● STEP 7 configurable/integrated as of version |
V5.5 SP3 / – |
● PCS 7 configurable/integrated as of version |
V8.1 SP1 |
● PROFIBUS as of GSD version/GSD revision |
One GSD file each, Revision 3 and 5 and higher |
● PROFINET as of GSD version/GSD revision |
GSDML V2.3 |
Operating mode |
|
● Oversampling |
No |
● MSO |
No |
|
CiR – Configuration in RUN |
Reparameterization possible in RUN |
Yes |
Calibration possible in RUN |
No |
|
Supply voltage |
Rated value (DC) |
24 V |
permissible range, lower limit (DC) |
19.2 V |
permissible range, upper limit (DC) |
28.8 V |
Reverse polarity protection |
Yes |
|
Input current |
Current consumption, max. |
150 mA |
|
Power loss |
Power loss, typ. |
1.5 W |
|
Address area |
Address space per module |
● Address space per module, max. |
8 byte; + 1 byte for QI information |
|
Analog outputs |
Number of analog outputs |
4 |
Voltage output, short-circuit current, max. |
45 mA |
Cycle time (all channels), min. |
5 ms |
Analog output with oversampling |
No |
Output ranges, voltage
|
● 0 to 10 V |
Yes; 15 bit |
● 1 V to 5 V |
Yes; 13 bit |
● -5 V to +5 V |
Yes; 15 bit incl. sign |
● -10 V to +10 V |
Yes; 16 bit incl. sign |
Output ranges, current |
● 0 to 20 mA |
Yes; 15 bit |
● -20 mA to +20 mA |
Yes; 16 bit incl. sign |
● 4 mA to 20 mA |
Yes; 14 bit |
Connection of actuators |
● for voltage output two-wire connection |
Yes |
● for voltage output four-wire connection |
Yes |
● for current output two-wire connection |
Yes |
Load impedance (in rated range of output) |
● with voltage outputs, min. |
2 kΩ |
● with voltage outputs, capacitive load, max. |
1 µF |
● with current outputs, max. |
500 Ω |
● with current outputs, inductive load, max. |
1 mH |
Destruction limits against externally applied voltages and currents |
● Voltages at the outputs |
30 V |
Cable length |
|
● shielded, max. |
1 000 m; 200 m for voltage output |
|
|
Analog value generation for the outputs |
|
Integration and conversion time/resolution per channel |
|
● Resolution with overrange (bit including sign), max. |
16 bit |
Settling time |
|
● for resistive load |
0.1 ms |
● for capacitive load |
1 ms |
● for inductive load |
0.5 ms |
|
Errors/accuracies |
|
Linearity error (relative to output range), (+/-) |
0.03 % |
Temperature error (relative to output range), (+/-) |
0.005 %/K |
Crosstalk between the outputs, min. |
-50 dB |
Repeat accuracy in steady state at 25 °C (relative to output range), (+/-) |
0.05 % |
Operational error limit in overall temperature range
|
|
● Voltage, relative to output range, (+/-) |
0.5 % |
● Current, relative to output range, (+/-) |
0.5 % |
Basic error limit (operational limit at 25 °C) |
|
● Voltage, relative to output range, (+/-) |
0.3 % |
● Current, relative to output range, (+/-) |
0.3 % |
|
|
Isochronous mode |
|
Isochronous operation (application synchronized up to terminal) |
No |
|
Interrupts/diagnostics/status information |
|
Diagnostics function |
Yes |
Substitute values connectable |
Yes |
Alarms |
|
● Diagnostic alarm |
Yes |
Diagnostic messages
|
|
● Monitoring the supply voltage |
Yes |
● Wire-break |
Yes |
● Short-circuit |
Yes |
● Group error |
Yes |
● Overflow/underflow |
Yes |
Diagnostics indication LED |
|
● Monitoring of the supply voltage (PWR-LED) |
Yes; Green PWR LED |
● Channel status display |
Yes; Green LED |
● for channel diagnostics |
No |
● for module diagnostics |
Yes; green/red DIAG LED |
|
Potential separation |
|
Potential separation channels |
|
● between the channels |
|
● between the channels and backplane bus |
● between the channels and the power supply of the electronics |
|
Isolation |
|
Isolation tested with |
707 V DC (type test) |
|
Ambient conditions |
|
Ambient temperature during operation |
|
● horizontal installation, min. |
-30 °C |
● horizontal installation, max. |
60 °C; Observe derating
-30 °C |
● vertical installation, min. |
● vertical installation, max. |
50 °C; Observe derating |
Altitude during operation relating to sea level |
|
● Installation altitude above sea level, max. |
2 000 m; On request: Installation altitudes greater than 2 000 m |
|
Dimensions |
|
Width |
15 mm |
Height |
73 mm |
Depth |
58 mm |
|
Weights |
|
Weight, approx. last modified: |
31 g |
01/20/2020 |
Analog Output Module 6ES7135-6HD00-0BA1
-
تماس بگیرید
*** Spare part *** SIMATIC ET 200SP, digital input module, DI 16X 24 V DC Standard, suitable for BU type A0, color code CC00, module diagnostics
-
0 تومان
منبع تغذیه 24 ولت 20 امپر مین ول (NDR-480-24) با توان خروجی 480 وات تحویلی به مصرف کننده اندازه گیری شده است. این محصول جزء سری ریلی پاور های مین ول محسوب می شود. راندمان این پاور به 92.5% می رسد که این خروجی ایده ال را مدیون استفاده از قطعات با کیفیت و طراحی سطح بالا می دانیم. تلفات در سوئیچینگ 24 ولت 20 امپر بسیار پایین اندازه گیری…
-
0 تومان
منبع تغذیه 24 ولت 62.5 آمپر مین ول با توان اندازه گیری شده 1500 وات واقعی در خروجی تحویل مصرف کننده قرار می گیرد. ولتاژ ورودی بین 180 تا 264 ولت ac و دارای مدار محدود کننده جریان در ورودی ، کنترل از راه دور و فن خنک کننده داخلی بلبرینگی DC از ویژگی های این محصول است.
-
0 تومان
منبع تغذیه 48 ولت 2.3 آمپر مین ول با توان اندازه گیری شده 110.4 وات در خروجی محاسبه شده است. این منبع تغذیه در دسته پاور های کف خواب شرکت مین ول قرار می گیرند. این منبع تغذیه سوئیچینگ این قابلیت دارد که به مدت 5 ثانیه ولتاژ ورودی تا 300 ولت را تحمل کند. راندمان در منبع تغذیه 48 ولت 2.3 آمپر به 91% می رسد که به راحتی…
-
0 تومان
منبع تغذیه 48 ولت 42 آمپر مین ول سری 48 RSP 2000 با توان 2016 وات واقعی در خروجی اندازه گیری شده است. یک از قابلیت های برجسته ی این سری از منبع تغذیه ها مین ول امکان موازی کردن تا چهار دستگاه با یک دیگر است به طوری که بتوان در خروجی با همان ولتاژ 48 ولت، جریان را حداکثر تا 168 آمپر افزایش دارد.
-
تماس بگیرید
نل لمسی (اچ ام ای) 9.7 اینچ وینتک (WEINTEK HMI) با رزولوشن 1024*768 ساخته شده است. HMI وینتک سری MT8092XE دارای صفحه نمایش از نوع TFT LCD همراه با نور پس زمینه LED می باشد. پردازنده به کار رفته در این پنل لمسی Cortex-A8 با فرکانس 1 گیگا هرتز و از نوع 32 بیتی می باشد. حافظه رم (RAM) در این HMI ، 256 MB می باشد. همچنین حافظه فلش…
Reviews
There are no reviews yet.